Clean Storm TurboBrite Air Duct Cleaning Silver Package Vacuum Driven

Description

TurboBrite Air Duct Cleaning Silver Package Vacuum Driven (Tool body + 4, 6, 8 and 3 pair of whips in case) [Turbobrite ZX Silver] 20220225
Video at
https://youtu.be/iC1_cl5HFdQ
Video at
https://youtu.be/Uo5cDHaBCKE
Can be used
with customer provided gas powered truckmounted carpet cleaning machines and all electric carpet cleaning machines with at least 6 stages of vacuum.
Contains:
1: Turbobrite spinning are duct tool (Ultra lite tool, 7 oz or 200 grams. Only 4.5" long)
1: 4" centering brush
1: 6" centering brush
1: 8" centering brush
3 pair: rotary brushes (9" but can be cut down to smaller size if needed) (turn at speeds up to 5000 rpm)
Work by the vacuum turning a turbine inside of the tool that causes the whips to turn.  The White certering brush is used to lift the tool body off the bottom of the duct so the whips can spin easier.
Click here to watch the video!
Turbobrite vacuum driven cleaning procedures (the vacuum turns the blue whips):
Carry 7 ft ladder (easy to move around in 8 ft ceilings) and 10 ladder (will fit inside the standard extended wheel base van) in truck as needed.
Take care of any paper work with customer.
Prep area as needed. (Move furniture to access vents, then cover nearby furniture with plastic to protect it.)
Turn off power to ventilation system.
After you perform your pre-inspection of the system both in the ducts and in the attic, put on your safety goggles and dust mask.
Remove vent covers and place in soapy cleaner in a plastic/rubber tub.
Scrub vents with upholstery brush and rinse off.
Leave vent covers on driveway to dry.
Carry a couple of cans of spray paint (in different colors) as an 'add on' to repaint vents after cleaning and before installation.
Install dust downer 50 ft from truckmount. This sprays water in the vacuum hose so your truckmount can deal with the mud and not dust. Vacuum ventilation system intake area with duster brush attachment. Replace and clean ventilation filter. (great add on to sell filters)
Place magnet on unit to remind your customer who to call. Place plain sticker and label with date of cleaning and estimated return appointment.
Use a 25 ft 1-1/2" vacuum hose leader. This is what is going to be fed into the duct.
Unscrew the hose cuff off the end of the vacuum hose. The Turbobrite tool screws into the threads on the inside of that vacuum hose leader. It is a real snug fit to insure if will not come off inside of the duct.
Attach the appropriate centering brush on the Turbobrite tool. All sizes are available from 4" to 10" in diameter.
Attach two whips that are long enough to lightly agitate duct. Whips are 9" long and can be trimmed to fit smaller ducts. The whips wear down and get smaller so save the whips as they wear down for the smaller ducts. Replacement whips are available.
Change out dust mask for respirator.
Feed Turbobrite down duct at a rate of 1" per second as far as you can and then pull the tool back out at 1" per second.
Clean carpet (if needed)
Fog with EPA approved duct sanitizer (if needed or paid for. 5 min. per duct @ 1.5 revolution on ULV fogger) Make sure customer does not breath atomized chemical.
Replace vent covers
Turbobrite Directions
Compatable with the following machines (short list) Goliath Extractor, Mytee 1005DX, Mytee 1003DX, Mega 3, Sandia 80-3500, Sandia 80-350H, All Galaxy dual 3 stage machines, all triple two stage machines, all gas powered carpet cleaning machines, Ninja dual 3 stage, Diamondback dual 3 stage,...many more.
The Turbobrite is a great entry level air duct cleaning unit for primary round ducts 10" or less
TurboBriteAirDuctSystemSilver; Shipping wt = 4#s; dimensions: 12 X 9 X 5
QB Assembly Includes:
(6) units - 3 pair of Whips
(1) ZX Tool body
(1) TurboBrite 4" Centering Brush
(1) TurboBrite 6" Centering Brush
(1) TurboBrite 8" Centering Brush
(1) Storage case (small Brand and type subject to change)